Wood Gate Costs in Fort Worth: Complete Price Guide

A basic walk gate in Fort Worth can cost as little as $250.Step up to a standard slat gate and wood gate costs in Fort Worth land at $350 to $650 installed. Go big with a wide or automatic driveway gate, and the total can hit $5,800 or more. That gap comes down to a few choices: the wood, the size, the style, the hardware and the soil your gate stands on.

Every price below comes from DFW Fence Contractor’s pricing guide, published May 19, 2025. In a few places that guide gave two numbers for one gate, so we blended them into a single range. Treat these wood gate costs in Fort Worth as ballpark figures, not quotes. Prices last reviewed November 2026. Fence Repair Texas installs and repairs wood gates for Fort Worth homeowners.

Table of Content

Wood Gate Costs in Fort Worth at first view

Plan on $250 to $650 for a single walk gate installed on existing posts. Large or automatic driveway gates can reach $5,800 or more. The table breaks wood gate costs in Fort Worth down by gate type.

Gate Type	Typical Installed Cost	What It Covers
Single walk gate (3 to 4 ft)	$250 to $650	Gate, hardware and fitting
Double walk gate (about 6 ft)	$500 to $1,500	Two leaves, hardware and fitting
Arched gate	$800 to $1,800	Extra labor for the curved top
Single driveway gate (about 10 ft)	$900 to $1,700	Heavier frame, posts and hinges
Double driveway gate (12 to 16 ft)	$1,500 to $3,000	Two heavy leaves and stronger posts
Sliding gate	$1,000 to $3,000	Gate, track or rollers and fitting
Automatic gate (opener included)	$2,000 to $5,800+	Gate, opener and fitting
Automatic opener (add-on)	$300 to $2,000	Motor and fitting
Gate repair	$100 to $600	Hinges or boards

Heavy or fully automated gates, particularly those with keypads, sensors and electrical work, can run past these ranges.

What Decides Wood Gate Costs in Fort Worth?

Seven things move the price. A few are obvious, like the wood itself. The season and the soil tend to catch people off guard.

Type of Wood

Pine is the cheapest wood, redwood is the priciest, and cedar falls in between. Cedar comes in more than one kind, though. Imported Japanese cedar costs less than Western Red Cedar, and the Western Red lasts longer. If you’re eyeing pressure-treated pine, look for AWPA UC3B treatment on pickets and rails and UC4A on posts that sit in the ground. Of the three woods, pine asks the most of you in upkeep, while redwood adds the most to wood gate costs in Fort Worth. Lifespans come up again further down.

Size and Height

Wider, taller gates eat up more lumber and need beefier posts, so the price rises with every foot. Single gates usually measure 3 to 4 feet across, double walk gates about 6 feet, and driveway gates 10 feet or more. Most stand 4, 5, 6 or 8 feet tall.

Design and Style

The cheapest style for wood gate costs in Fort Worth is a flat-top slat gate. Board-on-board costs more because it uses extra wood, but you get full privacy. Shadow box sits in the middle, with semi-privacy at a middle price. Arches, cutouts and trim take more time to build, and that labor shows up in your total.

Hardware and Accessories

Give hardware its own line in your budget for wood gate costs in Fort Worth. Basic hinges, a latch and a lock cost $50 to $100. Heavy-duty hardware runs $100 to $400, and decorative handles or lights add $50 to $200. An automatic opener is the big one at $300 to $2,000.

Labor and Installation

Installing one 4 by 4 foot gate takes roughly 2 to 4 hours. Double gates, wide 8- to 10-foot gates and electric openers can take a full day or call for a two-person crew. Some Fort Worth contractors charge $50 to $80 an hour per worker, while others quote a flat $150 to $300 for a standard walk gate. When the gate is heavy, wide or custom-wired, labor alone can run $400 to $800+.

Season

Fence crews stay busy in spring and summer. If you can hold off until fall or winter, you may see lower wood gate costs in Fort Worth.

Site Conditions

Your yard can change wood gate costs in Fort Worth too, since a sloped yard can call for extra bracing. Rocky ground makes digging tougher, and a tight work area slows the crew down. Taking out an old gate may cost extra. Fort Worth’s clay soil deserves its own section, and it gets one below.

Wood Gate Prices by Size and Style

A 4 by 4 foot slat gate starts at $350 to $650 in Fort Worth, and a custom arch gate with lights tops out around $2,700. Those wood gate costs in Fort Worth include the wood, the hardware and professional installation onto existing sound posts. New posts set in deep concrete footings, or hauling off an old gate, may push the total higher. Automatic openers and built-in mail slots are extra.

Gate Size and Style	Materials Cost	Labor and Hardware	Total Cost Estimate
4 by 4 foot simple slat gate	$150 to $250	$200 to $400	$350 to $650
6 by 6 foot board-on-board gate	$300 to $500	$300 to $600	$600 to $1,100
8 by 6 foot cedar shadow box	$400 to $700	$400 to $700	$800 to $1,400
10 by 6 foot redwood gate	$600 to $1,000	$500 to $900	$1,100 to $1,900
Custom arch gate with lights (e.g., 6 to 8 by 6 foot cedar/redwood, wired)	$800 to $1,500	$700 to $1,200	$1,500 to $2,700

Pine vs Cedar vs Redwood Gates: Cost and Lifespan

Cedar is the safe middle road for most gates, since it balances price against lifespan. Your budget for wood gate costs in Fort Worth still matters, along with how much sealing you’ll realistically do and how many years you want out of the gate. The table covers typical installed costs for a standard single walk gate, wood by wood.

Wood	Typical Cost per Gate	Rot and Insect Resistance	Upkeep	Lifespan With Care
Pine (untreated or pressure-treated)	$250 to $600	Low (untreated) to Good (pressure-treated, though prone to warping)	Seal often	5 to 12 years (shortest if sealing is skipped)
Cedar	$450 to $900	Good	Reseal regularly	15 to 25 years
Redwood	$600 to $1,200	Very good	Reseal regularly	15 to 25 years

The guide puts both cedar and redwood at 15 to 25 years when you look after them, so redwood’s higher price buys better resistance rather than extra years. Pine keeps wood gate costs in Fort Worth low up front. Skip the sealing, though, and it wears out sooner, and the repairs can swallow your savings. Exotic hardwoods like ipe or teak start around $1,000 per gate.

Walk Gates vs Driveway Gates: Swing or Slide

Walk gates usually swing. Driveway gates can swing or slide, and they cost a lot more because they’re larger, heavier and often automated.

A walk gate measures about 3 to 6 feet and handles people, pets and trash bins. Driveway gates are roughly 10 to 16 feet wide, come in single or double leaves, and need stronger posts, frames and hinges. Automation adds even more to wood gate costs in Fort Worth.

A swing gate needs open ground on the side it opens toward, at least as wide as the gate itself. A slope, a short driveway or a parked car can rule that out. A double swing gate splits the clearance between two leaves, so it works better on a tight drive.

If there’s no room to swing, a sliding gate may fit better because it runs along the fence line. It still needs a clear run beside the opening about as long as the opening for a ground-track gate (plus a track kept free of debris), or about 1.3 to 1.5 times the opening for a trackless cantilever gate that avoids clay-soil heave. When the ground slopes across the opening, grading or trenching may add to wood gate costs in Fort Worth, so ask an installer to check the grade.

Why Wood Gates Sag and How to Stop It

A wood gate starts to sag when the frame is weak, the hinges are too light for the weight, or a post has shifted in clay soil. Prevention starts with a compression-braced wood frame (diagonal brace running from the bottom hinge corner to the top latch corner) or a welded steel inner frame. Hinges rated for the gate’s weight, a stronger footing and good drainage at the base help too.

Not every sagging gate needs replacing. When only the hinges or a single board have failed and the posts are still sound, repair the gate. If a post has shifted in the soil, reset or replace the post. Replace the gate leaf itself only when the frame has twisted. Repairs run $100 to $600, far below full wood gate costs in Fort Worth, and our gate repair service covers common hinge, latch, board and post fixes.

How Fort Worth Clay Soil Changes the Price

Clay soil affects what a gate costs in Fort Worth more than most people expect. It swells when it’s wet and shrinks when it’s dry. Over time that movement pushes posts out of line, and the gate starts dragging or hanging crooked.

A gate post carries more weight and takes more stress than a fence post, so it needs a stronger footing to stay true. Typically that means 6×6 pressure-treated wood or heavy-gauge galvanized steel posts, set at least 30 to 36+ inches deep in bell-shaped concrete footings, crowned above grade to shed water. Installers price this work differently, so ask each one to spell out the post size, hole depth and concrete in the quote before you compare wood gate costs in Fort Worth.

Ways to Lower Wood Gate Costs in Fort Worth

Standard sizes and mid-range wood are the easiest places to save. Pre-cut gates cost less than custom ones, and cedar gives you good durability without the redwood price. Booking in the off-season and asking about winter discounts can take a little more off.

If you’re also building a new fence, bundling the gate in may lower the cost per gate, while a standalone gate job may carry a minimum or trip fee, so ask which one your quote assumes. Staining or painting the gate yourself is fine, but leave the posts and opener fitting to a pro. Buying hardware as a package and getting several quotes also helps.

How to Get an Accurate Quote

Start with a tape measure, then write down what you want so every quote covers the same work.

Measure the width, height and location, and note the soil type and slope.
Choose the wood: pine, cedar or redwood.
Choose the style: simple slats, board-on-board, shadow box or custom.
List the extras: hardware, lights, an opener (including safety sensors and 120V electrical trenching or solar power) and trim.
Ask what each quote includes, such as frame type (all-wood vs. welded steel inner frame), posts, footing depth, hardware, haul-away of the old gate and any electrical or permit work, so you can compare quotes like for like.
Decide on a budget range for wood gate costs in Fort Worth, share it, and ask a local fence company for a free on-site estimate.

Frequently Asked Questions About Wood Gates

These are the questions homeowners ask most about gate costs, materials and installation.

How much does a wooden gate cost?

In Fort Worth, a standard single wood privacy gate usually costs between $250 and $600 installed, depending on the size, wood type, and hardware. If you need a larger double-drive gate for a riding lawnmower or vehicles, the price typically ranges from $600 to $1,200 or more because it requires heavier framing, extra-duty posts, and reinforced hardware to prevent sagging.

What is the best wood for gates?

Western Red Cedar is widely considered the best overall choice for wood gates in Fort Worth because it naturally resists warping, shrinkage, and insect damage while holding up exceptionally well against harsh Texas heat. It stays lighter and straighter than other woods over time, giving you a clean look that lasts. If you are looking for a lower-cost option, pressure-treated pine is a popular alternative that handles local weather nicely as long as you keep it properly sealed and stained.

Can I install my own gate?

Yes, you can install your own wood gate as a DIY project if you have basic tools, a helper, and some patience. The biggest challenge is getting the posts set deep in concrete and keeping everything perfectly square so the gate doesn’t end up sagging under its own weight. If you want to skip the hassle of heavy-duty framing, alignment adjustments, and hardware installation, letting a professional handle it ensures your gate opens and latches smoothly for years.

How long does a wood gate last?

A well-maintained wood gate in Fort Worth typically lasts between 10 to 20 years, depending on the type of wood you choose and how well you care for it. Western Red Cedar usually outlasts pressure-treated pine because it naturally handles the intense Texas sun and weather without warping as quickly. Applying a fresh coat of stain or sealer every couple of years and keeping your hinges and latches properly adjusted are the best ways to stretch your gate’s lifespan and keep it working smoothly.

Do I need a permit?

For a standard residential gate or fence replacement in Fort Worth, you generally do not need a city building permit. A permit is typically only required if your overall fence or gate structure exceeds standard height limits—such as solid structures over 7 feet or open designs over 8 feet. or if your property is located within a designated historic district or special overlay zone. Checking with the Fort Worth building department before starting your project ensures you stay fully compliant with local rules.

How do I keep my gate from warping?

To keep your wood gate from warping in the harsh Texas heat, start by choosing a naturally stable wood like Western Red Cedar instead of standard pine. Building the frame with a strong diagonal brace running from the bottom hinge up to the latch side helps support the weight so the gate doesn’t sag or twist out of shape. Finally, applying a quality stain or waterproof sealer every couple of years blocks out moisture and intense UV rays, which are the main culprits behind drying, bending, and cracking.

What is the cost to repair a wood gate?

Repairing a wood gate usually costs between $100 and $300 for simple fixes like replacing a broken picket or tightening loose hinges. If the gate has bigger problems like a rotting post, a broken frame, or needs new heavy-duty hardware, the cost can range from $300 to $600 or more depending on how much work needs to be done.

Is an electric opener worth it?

An electric gate opener is definitely worth it if you have a driveway gate, because it saves you the daily hassle of getting out of your car in the rain, cold, or intense heat. Beyond everyday convenience, it adds an extra layer of security for your property and can even boost your home’s curb appeal. While automatic openers do cost more upfront and require occasional maintenance like checking batteries or remotes, the comfort and time-saving make them a very popular upgrade for homeowners.

How much space do I need for a swinging gate?

For a swinging gate, you need to make sure you have enough clear space for the panels to swing open completely without hitting cars, walls, or landscaping. A standard single gate requires an empty clearance arc equal to its width, usually between 3 and 4 feet. If you are putting in a double-drive gate for a vehicle or lawnmower, you will need a clear driveway span of 10 to 12 feet with enough swing radius on your property so the doors can open fully without blocking traffic or obstacles.

Can I match my gate to a new fence?

Yes, you can easily match your gate to a new fence, and building them together is actually the best way to ensure a seamless look. When you install both at the same time, your contractor can use the exact same wood type—like Western Red Cedar or pressure-treated pine—along with matching picket heights, board spacing, and trim styles so the gate blends right into the fence line. Even if you are adding a gate to an existing fence later on, a professional can usually match the wood grain and color with a fresh coat of stain so your property keeps a uniform and clean appearance.

In a Nutshell

Wood gate costs in Fort Worth come down to the wood, size, style and site, so budget for the frame, posts, footing, hardware and opener, and not only the boards. Pick the wood for the lifespan and upkeep you can live with, and the size and style for the privacy and driveway width you need. Before you decide, make sure every quote covers the same work. Then call Fence Repair Texas at (972) 525-9448 for a free estimate.